Challenger Mono Trunking
Challenger Mono Trunking
View the range
Challenger Trunking System
Challenger Trunking System
View the range
Mini Trunking & Accessories
Mini Trunking & Accessories
View the range
Maxi Trunking & Accessories
Maxi Trunking & Accessories
View the range
Conduit & Accessories
Conduit & Accessories
View the range
Channelling & Cable Protection Guard
Channelling & Cable Protection Guard
View the range
Loblite
Loblite
View the range
  •   01424 856600
  •    sales@bendex-plastics.co.uk
Bendex Plastics
  • Products
  • About Us
  • News
  • Collection Service
  • Contact Us

Challenger Trunking System

Easy to install three compartment data compliant trunking system, suitable for office, school or college environments.
Home » Challenger Trunking System » Fittings » Flat Tee

Flat Tee

Product code SystemPack QuantityVariation
XT1FTWHSystem 11N/A
XT2FTDWHSystem 21Down
XT2FTUWHSystem 21Up

View the technical specs
See other products in range
 

Other products in range

  • System
  • Product enquiry

System 1

System 2

Complete Unit

XT1CWH

Pack Quantity: 1 x 3m

XT2CWH

Pack Quantity: 1 x 3m

Trunking Base

XT1BWH

Pack Quantity: 4 x 3m

XT1BWH

Pack Quantity: 4 x 3m

XT1BWH

Pack Quantity: 4 x 3m

Centre Lid

XT1CLWH

Pack Quantity: 8 x 3m

XT1CLWH

Pack Quantity: 8 x 3m

XT1CLWH

Pack Quantity: 8 x 3m

Chamfered Lid Top/Bottom

XT1TBWH

Pack Quantity: 8 x 3m

XT1TBWH

Pack Quantity: 8 x 3m

–

Square Lid Top/Bottom

–

XT2TBWH

Pack Quantity: 8 x 3m

XT2TBWH

Pack Quantity: 8 x 3m

Coupler

XT1COWH

Pack Quantity: 2

XT2COWH

Pack Quantity: 2

End Cap

XT1ECWH

Pack Quantity: 2
Variation: N/A

XT2ECLWH

Pack Quantity: 2
Variation: left

XT2ECRWH

Pack Quantity: 2
Variation: right

Internal Bend

XT1IBWH

Pack Quantity: 2

XT2IBWH

Pack Quantity: 2

External Bend

XT1EBWH

Pack Quantity: 2

XT2EBWH

Pack Quantity: 2

Flat Angle

XT1FAWH

Pack Quantity: 1
Variation: N/A

XT2FADWH

Pack Quantity: 1
Variation: down

XT2FAUWH

Pack Quantity: 1
Variation: up

Flat Tee

XT1FTWH

Pack Quantity: 1
Variation: N/A

XT2FTDWH

Pack Quantity: 1
Variation: down

XT2FTUWH

Pack Quantity: 1
Variation: up

Surface Box 1 Gang

XTBB1WH

Pack Quantity: 20

XTBB1WH

Pack Quantity: 20

XTBB1WH

Pack Quantity: 20

Surface Box 2 Gang

XTBB2WH

Pack Quantity: 10

XTBB2WH

Pack Quantity: 10

XTBB2WH

Pack Quantity: 10

System 1

System 2

Technical specifications

Material

PVC-U is flame retardant and self-extinguishing. It provides a 100% recyclable material with good sustainability.

Installation

Positioning
When used as a skirting system a clearance of 10mm is recommended above floor covering to maintain IP4X rating.

Expansion/Contraction

PVC-U expands and contracts at a uniform rate of approx 5.25mm in a 3 metre length for a temperature change of 25°C. Therefore, a 3mm gap between each length of trunking base is recommended.
Fittings have a 10mm overlap on each side to allow for thermal movement of the covers.

Fitting

• Internal couplers on base units are not required. To fasten base, use No 8 round head screws and washers.
• Avoid over-tightening to permit thermal movement.
• The use of plastic caps over screw heads is recommended to protect installed cables.
• To cut the trunking, use a fine-toothed panel or power jig-saw.
• External moulded fittings overlap the joints by up to 10mm to cover cutting inaccuracies.
• A variable angle jig-saw or chop saw is recommended for cutting 45° mitres.

Single Lengths

Where it is required to fit a single length of trunking (under 3 metres) between two inside walls and no accessory box is fitted, it is advisable to install a coupler in the centre of the run to facilitate the removal of the cover.

Joints & Bends

• Base joints should have a 3mm gap to allow for expansion.
• Internal and external bends, the base must be mitred 45° to ensure total enclosure of trunking, including any internal fitted segregator.
• Flat tees and angles are prefabricated.
• External moulded fittings overlap the joints by up to 10mm to cover cutting inaccuracies

Covers

Covers are designed to limit unauthorised removal and to remain in position during normal conditions irrespective of impact and minor undulations of the mounting surface.

Covers Fitting

Covers are clipped into place from front.
If accessory boxes are installed, the XT1CLWH cover is butt-joined to the edge of the box. Cut edges of the cover are subsequently concealed by the accessory. For fittings, a gap of 25mm is left between the two cover ends to permit the fitting to clip to base.

Covers Removal

To remove a cover, first detach a coupler, internal or external bend component to gain access. The main cover can then be gently eased off the base. To remove the outer cover, firstly ease from the base by inserting the blade of a terminal screwdriver between the captive legs of the cover and the base and then ease away from the base.

Other ranges

Challenger Mono Trunking

Challenger Mono Trunking...

Single compartment dado trunking that can be subdivided, suitable for small office environments.
Read more
Mini Trunking & Accessories

Mini Trunking & Accessories...

Robust Mini trunking for domestic and commercial use. Available with accessories with self-adhesive backing.
Read more
Maxi Trunking & Accessories

Maxi Trunking & Accessories...

Strong and tough Maxi trunking and accessories manufactured from white PVC-U.
Read more
Conduit & Accessories

Conduit & Accessories...

Our popular range of conduit is manufactured in black and white PVC-U.
Read more

Download the latest
Bendex Catalogue

Your quick reference guide to Bendex products and services.

Download

Our ranges

  • Challenger Mono Trunking
  • Challenger Trunking System
  • Mini Trunking & Accessories
  • Maxi Trunking & Accessories
  • Conduit & Accessories

Contact us

  •   01424 856600
  •   sales@bendex-plastics.co.uk
  • Follow us on Twitter
  • Follow us on Facebook
  • Follow us on LinkedIn

Support

  • Downloads
  • Terms and Conditions
  • Privacy Policy
  • Website Terms and Conditions of Use

2021 © Copyright Bendex Plastics. All rights are reserved.

We use cookies on our website to ensure that we give you the best experience. By clicking OK, you consent to the use of cookies.OkPrivacy policy